How To Fix Wifi Antenna

We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

We recommend that you lot make clean your microwave earlier proceeding, as any nasty gunk on the bottom may finish upwards stuck to the iOpener.
Place the iOpener in the center of the microwave.
For carousel microwaves: Brand sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

Heat the iOpener for thirty seconds.

Estrus the iOpener for thirty seconds.
Throughout the repair procedure, equally the iOpener cools, reheat it in the microwave for an boosted xxx seconds at a time.
Be careful not to overheat the iOpener during the repair. Overheating may crusade the iOpener to burst.
Never touch the iOpener if it appears swollen.
If the iOpener is still too hot in the heart to touch, proceed using it while waiting for information technology to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

Remove the iOpener from the microwave, holding information technology past 1 of the two flat ends to avert the hot heart.
The iOpener will be very hot, so be careful when handling information technology. Use an oven mitt if necessary.

If yous don't have a microwave, follow this pace to heat your iOpener in humid h2o.
Fill a pot or pan with enough water to fully submerge an iOpener.
Heat the h2o to a boil. Plow off the heat.
Place an iOpener into the hot water for 2-three minutes. Brand sure the iOpener is fully submerged in the h2o.
Utilize tongs to extract the heated iOpener from the hot water.
Thoroughly dry the iOpener with a towel.
The iOpener will be very hot, so be careful to hold it only by the end tabs.
Your iOpener is ready for use! If you need to reheat the iOpener, oestrus the water to a boil, plow off the heat, and place the iOpener in the h2o for 2-iii minutes.

If your brandish glass is cracked, keep further breakage contained and prevent bodily impairment during your repair by taping the drinking glass.
Lay overlapping strips of articulate packing tape over the iPad's display until the whole face is covered.
This volition keep drinking glass shards contained and provide structural integrity when prying and lifting the display.
Practice your best to follow the rest of the guide as described. However, one time the glass is cleaved, information technology will likely continue to fissure as you work, and you may demand to utilize a metal prying tool to scoop the glass out.
Wear safe glasses to protect your optics, and exist careful not to damage the LCD screen.

Again, as you may detect yourself working with broken glass during this procedure, we strongly recommend wearing safety glasses for protection from flying shards.
Lay the iOpener apartment on the right edge of the iPad, smoothing it out so that there is good contact between the surface of the iPad and the iOpener.
Allow the bag sit on the iPad for approximately 90 seconds before attempting to open the front panel.

There is a pocket-size gap in the iPad'southward adhesive ring in the upper correct corner of the iPad, approximately 2.0 inches (~v cm) from the pinnacle of the iPad. You are going to exploit this weakness.
Align the tool with the mute button. Insert the tip of a plastic opening tool into the gap between the front drinking glass and the plastic bezel. Just insert the very tip of the opening tool, simply enough to widen the crack.
It may require some force to get the wedged tip of the opening tool betwixt the glass and plastic. Work patiently and advisedly, wiggling the plastic opening tool dorsum and forth as necessary.

Make sure y'all place the tool in the proper spot—between the plastic brandish bezel and the front panel glass.

Keeping the tip of the plastic opening tool wedged betwixt the front glass and plastic bezel, slide a plastic opening selection in the gap, right side by side to the plastic opening tool.

Remove the plastic opening tool from the iPad, and push the opening pick further underneath the forepart glass to a depth of ~0.5 inches.

While you work on releasing the adhesive on the right side of the iPad, reheat the iOpener, and replace information technology on the bottom edge of the iPad.

While the lesser border is beingness heated past the iOpener, brainstorm releasing the adhesive from the right edge of the iPad.
Slide the opening option downward forth the edge of the iPad, releasing the agglutinative as you go.
The adhesive is very strong, and some serious force may be required. Piece of work advisedly.
If you lot tin see the tip of the opening selection underneath the front drinking glass, pull the option out just a little bit. While using the opening pick this deep won't impairment anything, it may get adhesive balance all over the LCD.

It may exist necessary to move the heated iOpener back onto the right edge of the iPad equally you release the adhesive. This depends on how long the iPad has been able to cool while you were working on it.
If the opening choice gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.

Before removing the showtime opening pick from the bottom corner of the iPad, insert a 2nd pick under the right edge of the front drinking glass to keep the adhesive from re-adhering.
Re-estrus the iOpener, and move it to the tiptop border of the iPad.

The next few steps require extreme caution.
The Wi-Fi antenna is attached to the bottom right edge of the rear example of the iPad via screws and a cablevision. Because of the orientation of the Wi-Fi antenna, it is imperative to go along with caution otherwise irreversible harm to the Wi-Fi antenna may result.
You lot will have to release the agglutinative securing the antenna to the front panel without damaging the fragile parts attaching the antenna to the lesser of the iPad. Follow the adjacent steps carefully.

Slide the opening pick around the bottom right corner of the iPad, releasing the adhesive there.
Do not slide the choice further than the bottom correct corner. You may impairment the Wi-Fi antenna by doing then.

This step requires you to motility the opening pick along the bottom correct edge of the front panel. The Wi-Fi antenna is very close to the corner and is easily severed if the adhesive is released improperly.
Do not completely remove the option from under the forepart drinking glass, but pull it out just a little flake so that ~1/8" (3 mm) of the tip is nevertheless under the front glass.
Slide the tip of the opening pick along the lesser edge of the iPad, releasing the adhesive over the Wi-Fi antenna.

Once yous accept moved past the Wi-FI antenna (approximately 3" (75 mm) from the right edge, or right next to the domicile push) re-insert the opening pick to its full depth.
Slide the pick to the right, releasing the adhesive securing the Wi-Fi antenna to the front end glass.
The antenna is fastened to the bottom of the iPad via screws and a cable. This step detaches the antenna from the front panel, ensuring that when y'all remove the panel, the antenna will non exist damaged.

Continue releasing the adhesive forth the bottom of the iPad, pulling the opening pick out far plenty to go around the home button, and re-inserting it to a depth of i/2 inch (10 mm) in one case the option is past the home button.
If the adhesive has cooled too much along the lesser edge, reheat the iOpener to warm the adhesive where you are working.
Practice not heat the iOpener more than a minute at a fourth dimension, and always let at least two minutes before reheating it.

Continue releasing the adhesive all the mode along the bottom edge of the iPad.
On iPad iv models, insert the choice to a maximum depth of i/2 inch (10 mm) in this expanse, to avoid dissentious the home push button ribbon cable.
Leave the opening choice wedged underneath the front drinking glass about the habitation button.

Reheat the iOpener in the microwave and set it on the left edge of the iPad to start warming the adhesive in that department.

Slide the opening pick along the pinnacle edge of the iPad, pulling it out slightly to go around the forepart-facing photographic camera bracket.
The adhesive along this section is very thick, and a fair amount of forcefulness may be required. Work advisedly and slowly, making sure to not slip and impairment yourself or your iPad.
If the agglutinative has cooled likewise much, replace the iOpener along the acme edge and go on working. If the iOpener has cooled also much, reheat it.
If the opening option is getting stuck in the adhesive, "whorl" the option as shown in footstep 9.

Continue releasing the agglutinative along the tiptop edge of the iPad, and slide the opening pick effectually the top left corner.
If the adhesive is warm enough, remove the iOpener from the iPad for convenience. However, if the adhesive is all the same quite sticky, re-oestrus the iOpener and lay it on the left edge while you work.

Slide the opening pick along the left edge of the iPad, releasing the agglutinative as you go. The agglutinative is sparse here due to the digitizer along the whole left side. Brand sure the pick is not also deep (max 1/two inch) 10 mm to forestall dissentious the digitizer.
The digitizer cable is located approximately two" (l mm) from the bottom of the iPad. Stop sliding the choice when you become ~2.25" (60 mm) from the bottom of the iPad.

Using the opening pick that is all the same underneath the lesser edge of the iPad, release the agglutinative along the bottom left corner.
The bottom of the digitizer cablevision is simply ~1" (25 mm) from the bottom of the iPad. Work carefully and slowly, making sure to non sever this cable.

Using ane of the opening picks, pry up the bottom right corner of the iPad and take hold of it with your fingers.
Some of the adhesive along the perimeter of the iPad may take stuck back downward over again. If this is the case, slide a pick underneath the edge of the iPad where the front end drinking glass is still stuck and "cut" the agglutinative.

Holding the iPad by the superlative and lesser right corners, rotate the front glass abroad from the iPad.
Be careful of any agglutinative that may still be attached, and use an opening selection to cut any adhesive that may however be property the front panel down.
During reassembly use a microfiber cloth and compressed air to clean any dust or fingerprints off the LCD earlier reinstalling the drinking glass.

Remove the four two mm Phillips #00 screws securing the LCD to the aluminum frame.

Using a plastic opening tool or a spudger, lift the correct edge of the LCD out of the iPad.
Rotate the LCD forth its left border and lay it down on summit of the front end console.
Be careful as you move the LCD. The ribbon cablevision is frail and may break if information technology is flexed also much.

Using the tip of a spudger, pare back the piece of record covering the LCD ribbon cable connector.

Flip up the retaining flap on the LCD ribbon cable ZIF connector.
Using your fingers or a pair of tweezers, pull the LCD ribbon cable from its socket on the logic board.

Without touching the forepart of the LCD, elevator the LCD off the front console.

If necessary, peel back the piece of tape that secures the digitizer ribbon cable to the logic board.
Flip upwards the retaining flap on both of the digitizer ribbon cablevision ZIF connectors.

Use the flat end of a spudger to loosen the adhesive underneath the digitizer ribbon cable.
Very carefully pull the digitizer ribbon cable straight out of its sockets on the logic board.

Peel dorsum the digitizer ribbon cable and use the flat cease of a spudger to release the adhesive securing the cablevision to the rear aluminum instance.

Using your fingers, pull the digitizer ribbon cable out of its recess in the aluminum frame.
Remove the forepart panel from the iPad.

If present, remove the pieces of electric record covering the Wi-Fi antenna, speaker cable, and dock connector cable.

Use the flat finish of a spudger to pry the dock connector cable straight up out of its socket on the logic board.
Peel up the dock connector cable from the aluminum frame.